Honeywell HM509H8908 TrueSTEAM 9 Gal Humidifier w/H8908 Review

Average Reviews:

(More customer reviews)I installed this item in less than a day with a drill, 1 3/4 inch hole saw (rated for metal), wire cutters / strippers, pliers, nut drivers, screw driver with Torx bit, tubing cutter, brazing torch, solder, solder paste, sandpaper and a few other hand tools.
Having a down-draft HVAC and a slab foundation, I needed to install the control unit remotely from the HVAC supply thus I purchased the 10 foot remote option, installed the control on the blower chamber (which is above the furnace and ac coil), then installed the remote steam outlet between the furnace and ac coil below the control unit. Having installed the remote steam outlet below the control unit, "steam rated" t-fittings and p-traps were required as per Honeywell documentation (and common sense). Unfortunately, Honeywell does not offer "steam rated" t-fittings or p-traps as part of the high priced remote installation package ($150.00 plus for a plastic nozzle, 10 feet of insulated automotive radiator hose, two hose clamps, a few brackets and a few sheet metal screws), nor did any plumbing supply or "licensed installer" in my area or on the web, thus I made my own from 1/2 inch copper tubing, elbows, unions and t-fittings purchased from the local hardware chain for around $10. You will need a brazing torch, solder, flux, etc., to construct one, but it is easy.
I am not at all happy with Honeywell customer service, as they would not provide any technical information regarding return vs. supply installation, "steam rated" components, etc., unless I was a "licensed installer". I simply wanted to know if it was acceptable to install the unit in the return air system since, as previously noted, I have a down draft HVAC and a slab foundation, thus there is no access to the supply side. Ultimately, I had to rely on common sense and an understanding of summer humidity in Oklahoma; passing steam over the ac coil in winter would be no different than passing Oklahoma humidity over the ac coil in summer, thus installing the remote nozzle in the space between the furnace and ac coil should not present a problem.
One last note; the schematic for the "recommended" air flow detector may lead one to believe that the "C" wire between the HVAC and the TrueSteam is not required if you decide not to install the "recommended" air flow detector. The "C" wire IS required regardless of the installation of the air flow detector.
In summary, easy to install, but very, very low marks for Honeywell's pathetic customer service.
As a final note, the last "licensed installer" as recommended by Honeywell installed a whole house humidifier in my home that ended up costing me $3700.00 in damages. He wired the system to come on when the blower was on, and neglected to consider whether or not the AC or HEATER was on, thus the unit continually streamed moisture into the HVAC in the summer months. The result was standing, rotting water in the supply ducts. The entire HVAC had to be replaced at my expense since he filed bankruptcy. I won't be calling Honeywell for technical advice, and I advise anyone installing this system to do the same.


Click Here to see more reviews about: Honeywell HM509H8908 TrueSTEAM 9 Gal Humidifier w/H8908

Honeywell HM509H8908 rueSTEAM 9 Gal Humidifier W/H8908 HumidistatTrueSTEAM takes the best features from current steam humidifiers with their efficiency, performance and decreased water consumption, and combines it with the ease ofinstallation, reliability and value of flow-through humidifiers. TrueSTEAM is different from others because it operates independent of equipment operation.And, with its near 1:1 humidification delivery rate, TrueSTEAM delivers the right amount of humidification to keep your customers satisfied.Provides humidity independent of equipment operation, allowing homeowners to reach their desired humidity setpoints regardless of air temperature. Can be remotely mounted up to 20 feet from the system with purchase of remote mount kit- available in 10' or 20' Uses up to 70 percent less water to produce even more moisture than traditional whole-house humidifiers.Requires only a 1-3/4" cut into ductwork and mounts on a separate, lightweight bracket (included) for accurate leveling.Push terminals for easy wiring are routed through an interior harness so no wires are exposed. LED lights indicate when system is running or needs service. Lights also provide feedback to the installer during installation.Multiple sensors sit in a separate compartment to accurately monitor water levels.Application HumidificationType Steam ReservoirCapacity (gal. per day)9 gal per dayVoltage 120 VacMounting Duct or Remote MountTemperatureRange (F) 34F-104F

Click here for more information about Honeywell HM509H8908 TrueSTEAM 9 Gal Humidifier w/H8908

Read More...

Dustless Technologies MU405 Cougar Ash Vacuum, Black Review

Average Reviews:

(More customer reviews)With a fat Amazon gift certificate burning a hole in my jammies, visions of a clean coal stove danced in my head. I had been lusting after one of these ash-vacs for years, and now finally, it would be mine...
Boy do I wish I had read a review like this one prior to purchasing this vacuum (which I will return tomorrow). Didn't even have to dirty it, reading the instructions was all it took. Unfortunately, it required getting in to my livingroom to figure this out, since in none of the online descriptions at various sites, including Amazon, did it mention that this unit is for FINE ASH ONLY. In other words, the steel nozzle opening, approximately the diameter of a nickel, is designed to admit fine powder ONLY, and even that in small bits with the nozzle pressed against the firebrick in a "small circular pattern", allowing the ash to "sift" into the hose incrementally. (The instructions went on to detail all the various ways the thing could get itself plugged up...)
HELLO! Has anyone out there ever heated with solid fuel full time? It would take all day to suck up ash in that manner, not to mention that burning wood/coal does not produce exclusively fine ash. For coal especially, clinkers - the molten residue of trace minerals found in anthracite coal, are part of the bargain, and are produced in such abundance that it would render this tool effectively useless for coal burners.
In addition, though the hose is metal, intimating that the odd live coal is no biggie, the filter system in this thing is CLOTH - ie. you can burn holes in it with live material. Then it leaks. Right.
I'll have my 200+ bucks back and suck my ash chamber out with my shop vac, thanks - especially since the stuff would have to be cool anyway. (You can buy fine particle filters and bags at Home Depot). So much for my simplified stove cleaning fantasies...Oh well.

Click Here to see more reviews about: Dustless Technologies MU405 Cougar Ash Vacuum, Black

The Dustless Technologies MU405 Cougar Ash Vacuum lets you clean your fireplace, wood stove, or barbecue without making a dusty mess. Designed to remove warm-to-cold ashes, the Cougar is fire resistant and features a unique double filtration system that traps even the smallest dust particles.
Flame Resistant for SafetyThe Cougar is designed with safety in mind. It features a steel nozzle with a five-foot flame-resistant hose and a fireproof three-gallon steel chamber. The patented filter system uses fire-resistant fabric rated up to 1,200 degrees Fahrenheit, and the remaining parts are all made out of thermo-plastics to withstand high temperatures.
NOTE: Never use a household, or shop vacuum to clean a fireplace, because warm embers can be hidden under ash, which acts like an insulator and can keep embers hot for days after you think the fire is out. The combination of swirling air and debris inside a flammable paper bag filter is an extremely dangerous fire hazard.
Filter System Captures the Smallest Airborne Ash ParticlesThe Cougar features a double filter system that ensures no ash escapes the vacuum. This system leaves your air ash free and makes the process of cleaning your fireplace simple, clean, and healthy.
Each of the system's filters is designed to trap the finest ash, and the second filter even captures sub-micron particles. This double-filter action effectively traps ash, so your air stays clear.
Clean Filters Without Removing the LidYour Cougar's filters can be cleaned without removing them from the vacuum, eliminating any potential mess. For a quick dust-off, simply remove the brass cap from the lid and jiggle the agitator rod from side to side to shake the filters and make ash particles fall off.
After you have vacuumed up 60 to 80 gallons of ash, your Cougar will be ready for a thorough cleaning. Just detach and vacuum the secondary and primary filters to clean them.
Three-Gallon Canister Requires No BagsThe Cougar Ash Vacuum features a cold-rolled steel canister that will hold up to three gallons of ash. This fireproof canister safely contains your ashes without bags, so you'll never need to worry about expensive and annoying replacements. Just remove the canister's lid when it's time to empty your ashes.
Removes Ash Quickly and QuietlyThanks to its powerful, six-amp electric motor, the Cougar can suck up ash quickly and easily. What's more, specially designed motor housing makes operation as quiet as can be. In fact, the Cougar is the cadillac of ash vacuums, operating with 60% less noise than the Dustless Technologies Cheetah II.
To help speed up ash removal, the Cougar's crimped steel nozzle is designed to quickly pick up ash and leave larger debris behind--for burning at a later time. To use, just place the vacuum nozzle directly on the hearth and swipe it in a circular motion. Ash will flow smoothly through the hose without clogging.
WarrantyThe Dustless Technologies MU405 Cougar Ash Vacuum is backed by a one-year limited warranty for home use.
What's in the BoxDustless Technologies MU405 Cougar Ash Vacuum.

Get 4% OFF

Click here for more information about Dustless Technologies MU405 Cougar Ash Vacuum, Black

Read More...

Honeywell YTHX9321R5012 Prestige HD Thermostat Kit Review

Average Reviews:

(More customer reviews)The new Honeywell Prestige t-stat in the HD format is really a cool idea, I purchased this t-stat to replace the white rogers big blue, being certified to do A/C I thought this was going to be easy, some things to remember, 1. you need a 5 or more wire system on your A/C / Heat this thermostat takes a common wire to power it up, if you have only 4 wires then it will NOT work you will have to pull new wire from your control board to the t-stat, and forget about calling Honeywell customer service they are no help what so ever, after pulling new wire and doing the traditional hook up it was very easy to get this thermostat up and running it is very easy to program, I purchased the outside remote (wireless) to let me see what the weather outside was doing all in 1 place, this is a cool feature. I like the screen it is very well lit, it has very easy programs to operate through, like setting time, date cooling days ect The best feature is the clarity of the screen, at night in the absolute dark there is the thermostat all lit up easily read with the lights off, and you can adjust the screen brightness. There are a myriad of applications that can be chosen when programming, something I have never seen before in any programmable thermostat, I would suggest staying from installers mode, in that mode there are too many things you can mess up that are important that are pre set, I went in and only changes 1 thing, which was to let my A/C system had 2 stages, it comes set to 1 by the factory. All in all a great purchase if you can get over paying for cutting edge technology. I would highly recommended this thermostat!!!

Click Here to see more reviews about: Honeywell YTHX9321R5012 Prestige HD Thermostat Kit

Honeywell YTHX9321R5012 Prestige HD Thermostat Kit The Prestige HD thermostat provides control of 24Vac of heating and cooling systems. RedLINKenabled to work with compatible wireless accessories. The Prestige HD ThermostatKits contains Wireless Outdoor Sensor and High Definition (HD) Color TouchscreenThermostat Kit Includes: Prestige HDThermostat and Wireless Outdoor Sensor.Features: Large, easy-to-read backlit full color display shows current indoor temperature and humidity, temperature setting, date and time on the home screen. Also displays outdoor temperature and humidity on home screen (if wireless outdoor sensor is installed) Adjustable backlight level allows thermostat to be on full brightness at all times or dim to the brightness level of choice when the thermostat is not being used Interview-Based Programming wizard to easily and confidently schedule thermostat temperatures and timesUSB Port allows downloading of installer settings to quickly and consistently perform setup of thermostats in similar applications USB Port also allows easy setup of dealer logo and contact information on thermostat screen Real-Time Clock keeps time during power failure; automatically updates for daylight saving time Precise Temperature Control (+/- 1°F) for reliable and consistent temperature. Multiple HOLD options allows modification of schedule as needed Change Reminders to inform it is time to replace Air Filter, humidifier pad, ultraviolet bulb or batteries in connected devices RedLINK Enabled to communicate w

Click here for more information about Honeywell YTHX9321R5012 Prestige HD Thermostat Kit

Read More...

Ramsond CT520DY 3-in-1 Multi Function Air Inverter 50 Amp Plasma Cutter + 200 Amp TIG Welder + 200 A ARC/MMA Stick Welder: Auto Dual Voltage 110V/220V 50/60 HZ, 50 AMP Plasma Cutter + 200 AMP DC TIG Welder + 200 AMP ARC MMA Stick Welder Review

Average Reviews:

(More customer reviews)Because there was no feedback on this item I was very apprehensive about buying this item, however, I went ahead and bought it anyways. I got it today, opened it up, (it was well packed), put it together, (small amount assembly required), wired it up to 220, tested the plasma cutter and the arc welder and so far it has worked great. It is easy to operate and easy to move around.(though it is light weight it feels very solidly built)
So far I am VERY pleased with it.

Click Here to see more reviews about: Ramsond CT520DY 3-in-1 Multi Function Air Inverter 50 Amp Plasma Cutter + 200 Amp TIG Welder + 200 A ARC/MMA Stick Welder: Auto Dual Voltage 110V/220V 50/60 HZ, 50 AMP Plasma Cutter + 200 AMP DC TIG Welder + 200 AMP ARC MMA Stick Welder

Ramsond introduces the 4th generation of its CT520DY. CT520DY is a 3-in-1 multifunction cutting and welding machine. It is a 50 Amp plasma cutter, a 200 Amp DC (Direct Current) TIG welder and a 200 Amp ARC/MMA stick welder. It is dual voltage 110V/220V and dual frequency 50/60 Hz. It is equipped with DIGITAL AMP DISPLAY, INTEGRATED PRESSURE GAUGE, FOOT PEDAL FUNCTION and FOLDABLE INSULATED HANDLE. It uses the most reliable high frequency V-MOSFETs by TOSHIBA along with PWM (Pulse Width Modulation Processor) which help deliver a constant, concentrated and precise current to the cutting/welding surface. Regardless of your training, you can achieve smooth, clean and uniform cuts (1 inch) and weld a wide range of surfaces and material (e.g. stainless steel, carbon steel, alloy steel, copper, brass and other conductive material) with minimal heat input and without distortion of metal. CT520DY is easy to use by the do-it-yourself user, while fully accommodating of the demands of professional operators. It has five controls; the ON/OFF switch, Amperage Control Knob, the Post Flow Knob, Function Selector and the foot pedal ON/OFF switch. It has an integrated air pressure gauge in the front panel of the unit, as well as a large digital display that conveniently displays the current (Amps) setting of the unit. Note: This is a DC (Direct Current) TIG Machine. For aluminum welding AC (Alternating Current) is recommended. Each Ramsond CT520DY comes fully equipped with all accessories: TIG Torch, Plasma Torch, ARC/MMA Electrode Clamp, Air Regulator/Filter, Argon Flow Meter, Set of Consumables for the plasma and TIG torches, and Ground Clamp. Plug is not included. It comes with a 1 year Limited Warranty (Parts and Labor). The consumables are readily available both through Ramsond and third party sellers and are reasonably priced.

Click here for more information about Ramsond CT520DY 3-in-1 Multi Function Air Inverter 50 Amp Plasma Cutter + 200 Amp TIG Welder + 200 A ARC/MMA Stick Welder: Auto Dual Voltage 110V/220V 50/60 HZ, 50 AMP Plasma Cutter + 200 AMP DC TIG Welder + 200 AMP ARC MMA Stick Welder

Read More...

Advanced Tool Design Model ATD-6900 9-Piece HVLP Spray Gun Set Review

Average Reviews:

(More customer reviews)I was skeptical about this paint gun set, even though it was recommended to me by my cousin (a longtime painter). My body shop man tried it and was very impressed with the quality and result. It does not compare to a $500 paint gun, but it's definately better than many $250 paint gun sets.

Click Here to see more reviews about: Advanced Tool Design Model ATD-6900 9-Piece HVLP Spray Gun Set

Incredible value!Includes:(1) 1.8mm Primer Spray Gun; (1) 1.4mm Topcoat Spray Gun; (1) 1.0mm Touch-up Spray Gun, (2) 1 Liter Aluminum Cups, (1) 125cc Stainless Steel Cup.Also includes:(1) Regulator (0-180 PSI 0-12 BAR); (1) Face Mask; (1) Cleaning Kit; (1) Spanner Wrench; (1) Hex Wrench; (1) Brush; (2) Filters.

Get 31% OFF

Click here for more information about Advanced Tool Design Model ATD-6900 9-Piece HVLP Spray Gun Set

Read More...

Honeywell RTH6450D1009 5-1-1-Day Programmable Thermostat Review

Average Reviews:

(More customer reviews)I needed to replace my fifteen year old thermostat for one which was easier to adjust and change settings if needed. I chose Honeywell as they have always gave great life and service. I am using this on a steam heat system only, so I needed to connect only two wires. I did leave the jumper in as directed in the manual. I did power off my heating equipment (very important) we don't want surprises. This thermostat has a large display which can be back-lit simply by quickly pressing one of the control buttons. I only needed to program morning and night settings, you simply skip over the times you don't want to program. When in operation it displays both set temperature and room temperature. I would have to say it is accurate within +/- 1 degree as I compared it with three other thermometers. I installed the batteries before I attached it to the wall base and did all setting and programming ahead of time. The batteries are easy to replace when needed as they fit in a flip out holder from the side, no need to remove any covers or remove the thermostat from it's base.

Click Here to see more reviews about: Honeywell RTH6450D1009 5-1-1-Day Programmable Thermostat

Programmable 5 1 1 day with 4 program periods per day. For heating and air conditioning systems. Large backlit display with menu driven programming. Soft key controls. Shows room and set temperature. Exclusive Smart Response technology. Compatible with most electric, gas oil single stage furnaces; heat pumps without backup heat; heat only, and cool only furnaces. Will not work on electric baseboard heat. Precise temperature control + 1 F. Automatically switches from heat to cool to adjust the preheating cooling of your home so you can feel comfortable at your programmed times. Battery powered. Approximate size: 3.75'' H. x 6'' W. x 1.25 W. Off white. ENERGY STAR rated.

Get 21% OFF

Click here for more information about Honeywell RTH6450D1009 5-1-1-Day Programmable Thermostat

Read More...

Tjernlund Duct Booster Increases Heating and Cooling Power - 275 CFM Review

Average Reviews:

(More customer reviews)if you have areas of your home that are at the end of your hvac duct system and don't seem to be putting out either the heat or coolness that you want, then buy and install this product pronto. install time was less than an hour. instructions provided by northern tool were excellant, and wiring to furnace was easy. doubled the airflow of vents at the end of my duct system. i highly endorse this product as this is the third one that i've purchased. installed one about eight years ago and have had no problems with it at all.

Click Here to see more reviews about: Tjernlund Duct Booster Increases Heating and Cooling Power - 275 CFM

Increases heated or cooled air flow to problem rooms up to 50%! Squirrel-cage style Duct BoosterÆ installs in ducts 5in. in diameter or more and in rectangular ducts at least 3 1/4in. deep. Dependable 40 Watt Fasco motor moves 275 CFM free air, draws .51 Amps. UL listed. Auto and Manual: Yes, CFM: 275, Works With: Heating and cooling ducts, Amps: 1/2, Motor: 40 Watt Fasco motor, Mount Type: Mounting template included, Dimensions L x W x H (in.): 7in. Length and 4in. diameter, Includes: 1 Booster fan

Click here for more information about Tjernlund Duct Booster Increases Heating and Cooling Power - 275 CFM

Read More...

Slant/Fin 6-Pack Mineral Absorption Pads Review

Average Reviews:

(More customer reviews)Decent price but the cost of shipping makes it almost prohibitive. It is so light and compact, it could have been put in a small envelope and sent for less than $1. Unfortunately there is no other source I could find.

Click Here to see more reviews about: Slant/Fin 6-Pack Mineral Absorption Pads

For Germ-Free Humidifiers: GF-200

Click here for more information about Slant/Fin 6-Pack Mineral Absorption Pads

Read More...

Avanti Thermoelectric Cold Water Dispenser (White) (15"H x 10.75W x 12"D) Review

Average Reviews:

(More customer reviews)1st of all: do NOT believe the instruction booklet when it says not to wash out the unit before use! (They claim it comes ready for use from the factory.) It gave a really "off" flavor to the water till I rinsed out the unit thoroughly with baking soda dissolved in water. DO believe the people who say it takes a long time for water to get cold--it really does, especially the first time you use it. That said, we really like this unit now. It fits nicely on the counter, is easy to use, and provides our family of two with enough cold water.

Click Here to see more reviews about: Avanti Thermoelectric Cold Water Dispenser (White) (15"H x 10.75W x 12"D)

Always have fresh, cold water to enjoy in your home or office with this Avanti Thermoelectric cold water dispenser. This is the counter top model, with a non-compressor system. The compact design fits easily in the home or office environment and holds standard sized bottles, 3or 5 gallons. The light weight and energy efficient system can dispense cold or room temperature water and has a removable drip tray. The water bottle is not included.Assembly level/degree of difficulty: No Assembly Required.

Get 28% OFF

Click here for more information about Avanti Thermoelectric Cold Water Dispenser (White) (15"H x 10.75W x 12"D)

Read More...

Yard Machines 11A-020B000 20-Inch 148cc Briggs & Stratton 300 Series Mulch/Side Discharge Gas Powered Push Lawn Mower Review

Average Reviews:

(More customer reviews)I bought this mower about 5 years ago. A single woman, I never paid attention to oil changes or maintenance schedules. Just a week ago, I though I needed a new machine when the cord got stuck and would not recoil. It motivated me to learn to do my own maintenance on the mower.
A clean, new air filter, a freshly sharpened blade and a new spark plug later with a healthy oil change proved to me how resilient this little machine is, and how sturdy it is. With its new parts and a good clean up, the little thing started working like new.
If it can endure my abuse, believe me, it is a good product! I mow an area of about 1/8 acre. Very, very happy with my machine that is still faithful to my yard.

Click Here to see more reviews about: Yard Machines 11A-020B000 20-Inch 148cc Briggs & Stratton 300 Series Mulch/Side Discharge Gas Powered Push Lawn Mower

Features a 148cc, Briggs & Stratton 300 series engine push mower. 20-Inch steel deck with side bag capabilities.

Get 22% OFF

Click here for more information about Yard Machines 11A-020B000 20-Inch 148cc Briggs & Stratton 300 Series Mulch/Side Discharge Gas Powered Push Lawn Mower

Read More...

Broan Replacement Range Hood Fan Motor and Fan - 2 Speed # 97012248, 1.1 amps, 120 volts Review

Average Reviews:

(More customer reviews)I bought this to replace an old fan that died on my range hood. It was the exact same as the one I replaced but the fan rotated the opposite direction, so it was blowing the air down. After switching the installation bracket the opposite way it no longer fit because the filter and bulb got in the way. I put it back to how it was but when I switched it between high and low speeds a few times the motor blew out. At least this gave me an excuse to buy a new range hood.

Click Here to see more reviews about: Broan Replacement Range Hood Fan Motor and Fan - 2 Speed # 97012248, 1.1 amps, 120 volts

Cross Reference: 42000, 2S-67N3, 8326017869, 99080533, 97012248, 99080492, 17869, P-12432, P-14780A, P-15360, RL6100-H, RL6300-H, F40000, RL6100F-R, 34000, 35000, 36000 Range Hoods

Click here for more information about Broan Replacement Range Hood Fan Motor and Fan - 2 Speed # 97012248, 1.1 amps, 120 volts

Read More...

Wagner 0518050 Control Spray Double Duty Paint Sprayer Review

Average Reviews:

(More customer reviews)I did a fair amount of web research before using the Control Spray Double Duty.. after reading the other reviews I'm glad I did. With the proper prep work and techniques this spray gun has worked quite well for us.
Yes, the paint needs to be very thin.. not quite 'water thin' as one reviewer stated, but definitely thin. On average plan on 4 parts paint to one part water (or whatever thinner you're using).. at least for average latex paint using the CS Double Duty model. I understand with the original (and less powerful) Control Spray it's closer to 2:1. A viscosity tester comes with the painter.. a small funnel type cup that you dip into the paint, and then time how long it takes for the paint to flow out the bottom. There's a chart in the instructions that will tell you what the time should be for various types of paints (oils, varnish, stains).. but mine at least didn't include times for latex paints. Approx 65-70 seconds worked well for us.
We strained the paint each and every time we filled the paint cup. Debris, dust, hair.. tiny specks of who knows what floating in the air can land in your paint and clog the gun and stop or weaken the flow. We did have to experiment a few minutes with distance and speed to get the right coverage, but there was no spitting or clogging at any time, and the spray was fine and even. There was very little overspray.
Cleanup is easy, but must be done each time you stop spraying. The gun does heat a bit, and the paint is so thin it will 'bake' onto the innards if you let it sit.. so if you need to wait 20 or 30 minutes (or longer) for a coat to dry before you put down your next one, you'll have to clean the gun in the meantime. Luckily, it's easy and fast.. there are actually very few parts to clean.. and takes less than 5 minutes once you've done it a time or two. For latex, lukewarm water and soap was all that was needed.
Be prepared to take some time.. we found that numerous thin coats, with strokes that overlapped about 60% worked best.. at least for our project. We just finished painting our kitchen cabinets.. an excruciating and painstaking process, made considerably easier once we purchased the Control Spray Double Duty. It took some experimentation but we achieved beautiful, mirror-smooth finishes on all our cabinets and drawers. Again, this took time and effort.. but was definitely worth it. We plan on using the CS Double Duty to do a set of louver doors next, and to stain our back deck this summer.


Click Here to see more reviews about: Wagner 0518050 Control Spray Double Duty Paint Sprayer

Wagner's paint sprayer with HVLP technology gives you maximum control with 3 spray patterns and a variable-control trigger with patterns from 1 to 10in. Sprayers help you get the job done fast, whether you're just painting the kitchen or an outside wall. Nozzles Included (qty.): 1, Case Included: No

Get 11% OFF

Click here for more information about Wagner 0518050 Control Spray Double Duty Paint Sprayer

Read More...

The Dust Deputy DIY Review

Average Reviews:

(More customer reviews)I purchased the molded Dust Deputy to attach to my RIGID shopvac. The deputy worked well in separating fine particles of dirt and dust and made a huge difference in keeping the shopvac's filter clean. The kit was easy to assemble but I was concerned with the rigidity of the top lid of the plastic bucket where the cyclone attaches. The lid flexes under the weight of the cyclone and seems flimsy. I modified the top lid by constructing a plywood disk that attaches on the bottom side of the lid to add support for the cyclone separator. This keeps the plastic lid from sagging under the weight of the cyclone separator and helps keep it snapped tight to the lower bucket.
If you purchase this unit, be careful not to drop it, mine fell to the floor when the suction hose became trapped and I pulled the shopvac by the handle. The unit with the hoses attached fell on the concrete floor and shattered. I am not sure what type of plastic it is made of, but so far it has resisted the effects of many types of glue commonly available. I have since purchased the metal version of the Dust Deputy, it is much more robust and fits perfectly in the existing hardware contained in the plastic kit. I am very happy with the performance with the Dust Deputy, but you may consider spending a little more money to purchase the more robust metal version.


Click Here to see more reviews about: The Dust Deputy DIY

ON SALE!For a limited time, the Dust Deputy DIY is $20.00 off! Prior sales excluded.The Dust Deputy is an extremely efficient, cyclonic pre-separator for vacuums. Trap dust in the barrel and NOT in your shop vacuum. The Dust Deputy will filter 99% of sanding dust, with only 1% going into the vacuum. Extend the life of your shop vacuum and your filters! The Dust Deputy is injection molded from translucent, static dissipating plastic. Added to your existing shop vacuum, it uses centrifugal force to literally spin the material being conveyed right out of the airstream, and into the bucket. 99% of the material NEVER reaches your shop vacuum! The DIY kit includes the cyclone ONLY.Flat rate shipping to the Lower 48 United States only $12.50. Alaska, Hawaii, Canada, and all other countries, please call 800-732-4065 for shipping arrangements.

Click here for more information about The Dust Deputy DIY

Read More...

Trend Airshield Face Shield Review

Average Reviews:

(More customer reviews)The Airshield is a needed accessory for many types of woodworking. It works well but is hampered by an ungainly procedure to change batteries and choice of materials and construction that does not hold up to extensive use. My airshield has ended up with numerous super glued joints and replaced rivets. Perhaps the Airshield Pro is designed better but the standard airshield does not hold up to continuous use.

Click Here to see more reviews about: Trend Airshield Face Shield

Lightweight battery-powered face shield circulates air while protecting your eyes and face from small debris such as wood particles and wood shavings. Ideal for routing and woodturning. Specifications: * Flow rate 6.36 cf/min.; minimum 4.94 cf/min.* Eye protection to ANZI 287.1 (low-energy impact). * Respiratory protection (NPF20) to EN 146 THP2. * Fits 20-1/2" to 24-1/2" head sizes. * Weighs only 1.62 lbs. * Comes with rechargeable 4-hour Nicad battery pack and 120V charger. * Instructions included.

Click here for more information about Trend Airshield Face Shield

Read More...

SEISSE Single Lever Kitchen Chrome Filter Water Faucet Review

Average Reviews:

(More customer reviews)I used one of these for several years. This is NOT made of the very best materials as the manufacturer claims, it is made of chrome plated brass. Water products like this will corrode and self-destruct eventually as mine did because the water is in contact with the brass. The very best material would be stainless steel.

Click Here to see more reviews about: SEISSE Single Lever Kitchen Chrome Filter Water Faucet

SEISSE Filtered Water Faucet - SEISSE is a Switzerland based company designing only the very best water filtration and purification products, promoting a healthier and Greener tomorrow.  All products contain the very best in materials and workmanship and are backed by a 1 YEAR Warranty. Your SEISSE Filtered Water Faucet includes: High Grade Chrome Finish faucet, Non Air Gap Technology, ¼" tube connection, ¼" brass mount included, All installation accessories, 1 YEAR warranty. Brass Construction - 1.2 GPM / 4.5 LPM @ 60 PSI - Deck Mount on Kitchen Sink or Counter Top - Faucet Height 10 1/2" - Spout Reach 4 3/4" - Spout Clearance 8 1/2" - 1/4 Ceramic Disc Cartridge - Single Hole Mount - 1/4" IPS Inlet Water Line Connection. The best quality at the best price. Don't cut corners when it comes your personal home products. When only the very best will do, buy SEISSE for maintenance-FREE enjoyment. SEISSE. Not just a faucet, but a fashion statement.

Click here for more information about SEISSE Single Lever Kitchen Chrome Filter Water Faucet

Read More...

Industrial Grade 2EWX9 Auto Air Purifier, 12V, Solar Review

Average Reviews:

(More customer reviews)very pleased with ease of set up, and it seems to be working great, we have it plugged in as its winter and our van is garage kept, but it tested good under solar power, the fragrance beads wear out fast, but i was sent some more for free, we smoke in our van and it seems to be cleaner and windshield is free of smoke film, we are happy with the service we recieved.

Click Here to see more reviews about: Industrial Grade 2EWX9 Auto Air Purifier, 12V, Solar

Air Purifier, Auto, Voltage (DC) 12, Rated Watts 10, Coverage 161 Square-Ft, Dimensions 7 1/2 x 5 5/16 x 1 5/8 In, Features Solar Energy or 12V DC Operation,Auto (Vibration Sensitive) and Manual Operation,TiO2 Filter,Carbon Filter,UV Filter,Negative Ion Generator,Two speed, Used For Vehicle Air Purification, Includes 12V DC Power Cable, and Auto Glass Suction Cup Mounting Bracket

Click here for more information about Industrial Grade 2EWX9 Auto Air Purifier, 12V, Solar

Read More...

Protemp Portable Kerosene Forced Air Heater - 70,000 BTU, Model# PT-70T-KFA Review

Average Reviews:

(More customer reviews)I BOUGHT THIS HEATER FOR MY GARAGE WHICH IS 20 X 25 (500SQ. FT.)AND IN THE DEAD OF WINTER IN A UNINSULATED GARAGE IT HEATED THE PLACE IN 15 MINUTES TO 70 DEGREES. THE FOLLOWING YEAR AFTER I INSULATED THE GARAGE IT TOOK 10 MIMUTES, BUT BEING INSULATED IT RETAINED THE HEAT MUCH LONGER . SO EITHER WAY IT WORKS GREAT AND IT HAS IT'S OWN THERMOSTAT , KEN FROM PA.

Click Here to see more reviews about: Protemp Portable Kerosene Forced Air Heater - 70,000 BTU, Model# PT-70T-KFA

The Protemp 70,000 BTU portable kerosene forced air heater with high-performance fan delivers powerful instant heat to create a warm, comfortable environment for work spaces, construction sites and workshops.

Click here for more information about Protemp Portable Kerosene Forced Air Heater - 70,000 BTU, Model# PT-70T-KFA

Read More...